Поддържа Polaris карти RX - сериите.
Сваляне:
http://ethosconfig.free.bg/atiflash_linux.tar.xz - версия 4.25
Инсталация с една команда:
- Код за потвърждение: Избери целия код
wget http://ethosconfig.free.bg/atiflash_linux.tar.xz -O /tmp/atiflash_linux.tar.xz && sudo tar xvf /tmp/atiflash_linux.tar.xz -C /usr/local/bin/
Команда за лист на адаптерите:
- Код за потвърждение: Избери целия код
sudo atiflash -i
Други команди:
- Код за потвърждение: Избери целия код
--- ATIFLASH v4.25 ---
-h, -?, /h, /? Help (this screen)
Format: ATIFLASH [command] [parameter1] [parameter2] [parameter3] <option/s>
[command]:
-i [Num] Display information of ATI adapters in the system.
Display information of adapter [Num] if specified.
-ai [Num] Display advanced information of ATI adapters on system.
Display advanced information of adapter [Num]
if specified.
-biosfileinfo <File> Displays the Bios info in file <file>
-p <Num> <File> Write BIOS image in file <File> to flash ROM in Adapter
<Num>.
-pa <File> Write BIOS image <File> to all appropriate adapters.
-s <Num> <File> [Size] Save BIOS image from adapter <Num> to file <File>.
First [Size] kbytes (except for Theater in bytes) of ROM
content is saved if [Size] is specified.
-cf <File> [Size] [Sum] Calculate 16-bit checksum for file <File>.
Checksum for the first [Size] kbytes of the file is
calculated if [Size] is specified.
-cb <Num> [Size] [Sum] Calculate 16-bit BIOS image checksum for adapter <Num>.
Checksum for the first [Size] kbytes of the ROM content
is calculated if [Size] is specified.
-cr <Num> [Size] [Sum] Calculate 16-bit ROM checksum for adapter <Num> and
compare it to the [Sum] specified. This command is
the same as -cb if [Size] is specified.
-t <Num> Test ROM access of adapter <Num>
-v <Num> <File> Compare ROM content of adapter <Num> to <File>
-mi <Num> [ID] Modify SSID & SVID in BIOS image of adapter <Num> to
<ID>. SSID & SVID in BIOS image of adapter <Num> is
displayed if [ID] is not specified.
-mb <Num> <File> Modify SSID, SVID, BIOS Pin Number, & Boot Message in
BIOS image of adapter <Num> to values in <filename>.
Input file example:
ssid = 715B
svid = 1002
biospn = "113-xxxxxx-xx"
bootmsg = "ATI graphic board"
-pak <File> Package an executable for BIOS update according to
the commands in <File>.
Config file example:
outfile = update.exe
banner = "Update v1.0"
infile = a123.bin
command = -pa -padevid=715B infile
-isr <Num> <Build Number> <Board Number> Set ISR number based on the given
build and board number
if not specified, print out ISR Number
-prod <Num> <12 digit serial number> Set PROD number based
on the given serial number
if not specified, print out SN Number
-checkprodsn <Num> <12 Digit Serial Number> Comparing the Prod SN based on
existing prod sn saved in ROM
<option/s>:
-f Force flashing regardless of security checkings (e.g. AsicID &
BIOS file info check OR boot-up card).
-fa Force flashing bypassing already-programmed check.
-fm Force flashing bypassing BIOS memory config check.
-fs Force flashing bypassing BIOS SSID check.
-fp Force flashing bypassing BIOS P/N check.
-nw No user interaction on test failure.
-sst Use SST25VFxxx flashing algorithm regardless of ROMID straps.
-st Use ST M25Pxx flashing algorithm regardless of ROMID straps.
-atmel Use AT25Fxxx flashing algorithm regardless of ROMID straps.
-nopci Do not enumerate PCI adapters, i.e. enumerate only AGP and
PCIe adpaters
-pcionly Enumerate only PCI adapters, i.e. do not enumerate AGP and
PCIe adapters
-agp Enumerate only AGP adapters, i.e. do not enumerate PCI and
PCIe adapters unless used with -pcie or -pci
-noagp Do not enumerate AGP adapters, i.e. enumerate only PCI and
PCIe adpaters
-pcie Enumerate only PCIe adapters, i.e. do not enumerate AGP and
PCI adapters unless used with -agp or -pci
-nopcie Do not enumerate PCIe adapters, i.e. enumerate only AGP and
PCI adpaters
-pci Enumerate only PCI adapters, i.e. do not enumerate AGP and
PCIe adapters unless used with -agp or -pcie
-noremap Skip BARs error detection and remapping in PCI configuration
space
-reboot Force a reboot of the system after successfully completing the
specified operation
-keepisrsn keep the ISR Number on the adapter when flashing a new VBIOS
-keepprodsn keep the Prod SN on the adapter when flashing a new VBIOS
-siireset Specifies the GPIO Pin to be used as the Reset when updating
SiI1930 microcontroller firmware
Input example:
-siireset=7 <No Spaces>
-siiuprog Specifies the GPIO Pin to be used as the uprog when updating
SiI1930 microcontroller firmware
Input example:
-siiuprog=14 <No Spaces>
-scansii Overrides normal adapter detection to enable detecting SSI
roms with/without TPI firmware
-log Logs output to atiflash.log, overrides existing file
-logappend Logs and appends output to atiflash.log
-ddc Enable DDC support
-padevid=<ID> Use with -pa command to update adapters of specific device ID.
-passid=<ID> Use with -pa command to update adapters of specific SSID.
-pasvid=<ID> Use with -pa command to update adapters of specific SVID.
-pavbpn=<VBPN> Use with -pa command to update adapters of specific VBIOS PN.
-excl_memtrain_dtable When flashing on new VBIOS, a pre-determined memory
training data table in the old VBIOS will not be
overwritten.
-isr <adapter num> [build num] [board num] If build number and board number
are specified, sets the ISR Number
value in specified adapter.
If only adapter is specified, the current
ISR Number is displayed
-checkpn <adapter num> <filename> Checks PN of the current product
and compares it to external file
*<Num> = adapter number, <File> = filename
*[Size] = data block size in KBytes, except for Theater Pro in Bytes
*Use command -i to see the adapter numbers in the system.
*Theater Pro supports commands -i, p, s, cf, cr, t, v and options -f, -noremap.
